Tutorial Avolites Titan Art-Net and CITP: Difference between revisions

From MXWendler Wiki
Jump to navigation Jump to search
Line 109: Line 109:
:check the cable, check switches/hubs if there are any, make sure firewalls are off, make sure both computers  
:check the cable, check switches/hubs if there are any, make sure firewalls are off, make sure both computers  
:are correctly identified…
:are correctly identified…




Line 116: Line 114:




* From the System/Setup menu (hit <Avo> and <Disk>), select DMX Settings.  
From the System/Setup menu (hit <Avo> and <Disk>), select DMX Settings.  
:Left, in the Art-Net section, you should be able to see entries like this:  
:Left, in the Art-Net section, you should be able to see entries like this:  
::::''MXWendler(IP address): Universe x''
::''MXWendler(IP address): Universe x''
:Click on the entry with ''Universe 1'', then, on the right-hand side,  
:Click on the entry with ''Universe 1'', then, on the right-hand side,  
:click on ''Line 1'', to route the signal from internal line 1 to Art-Net universe 1.
:click on ''Line 1'', to route the signal from internal line 1 to Art-Net universe 1.




* Next, check the Art-Net settings are correct:  
Next, check the Art-Net settings are correct:  
:left, at the Art-Net line, click on the little ''I''  
:left, at the Art-Net line, click on the little ''I''  
:(in newer versions a symbol like this:[[File:avo 04.PNG]])  
:(in newer versions a symbol like this:[[File:avo 04.PNG]])  
:and make sure the settings are correct:
:and make sure the settings are correct:
:::''Enable DMX Output = Enabled''
::''Enable DMX Output = Enabled''
:::''Always Broadcast ArtNet = Enabled''
::''Always Broadcast ArtNet = Enabled''
:::''Network Adapter = the network adapter which you have configured''
::''Network Adapter = the network adapter which you have configured''


* Exit the System/Settings menu.  
Exit the System/Settings menu.  


* You are now ready to patch and control MXWendler manually: <Patch>, <Fixtures>,  
You are now ready to patch and control MXWendler manually: <Patch>, <Fixtures>,  
:select manufacturer MXWendler,  
:select manufacturer MXWendler,  
:select fixture MXWendler v5,  
:select fixture MXWendler v5,  
Line 145: Line 143:
'''3. CITP setup'''
'''3. CITP setup'''


* Restart MXWendler again. This is required to refresh/activate the CITP data exchange.
Restart MXWendler again. This is required to refresh/activate the CITP data exchange.


*On the Avo console, press ''<Patch>'' and select Active Fixtures.  
On the Avo console, press ''<Patch>'' and select Active Fixtures.  
:MXWendler should be shown in the list of available active fixtures:
:MXWendler should be shown in the list of available active fixtures:
[[File:avo 06.png|60px]]
[[File:avo 06.png|60px]]


* Click on this button. Usually the software sends the correct addressing automatically  
Click on this button. Usually the software sends the correct addressing automatically  
:(you can leave the next item on ''Use Fixtures Dmx Address''.)  
:(you can leave the next item on ''Use Fixtures Dmx Address''.)  
:Simply click on an empty fixture button. 8 layers will automatically be patched:
:Simply click on an empty fixture button. 8 layers will automatically be patched:
Line 157: Line 155:
[[File:avo 07.png|628px]]
[[File:avo 07.png|628px]]


*In order to see thumbnails of your media select a mediaserver layer,  
In order to see thumbnails of your media select a mediaserver layer,  
:open the Attribute Editor (e.g. with ''<Open>-<Options>''), and go to the Gobo bank:
:open the Attribute Editor (e.g. with ''<Open>-<Options>''), and go to the Gobo bank:


[[File:avo 08.png|628px]]
[[File:avo 08.png|628px]]

Revision as of 13:40, 18 March 2019

How to network an MXWendler mediaserver with an Avolites Titan lighting console.
March 2016, with MXWendler version 5 and Avolites Titan version 9.


{{#mpdftags: pagebreak}}

Pre-requisites:

Standard Art-Net control:

simply use the Avolites personality MXWendler_MXWendler v5.d4
If it is not already present on your console then you can load it as a user personality
(on consoles in the folder D:\Personalities).
The file CitpFixtureMapping.xml is not required in this case.


Full CITP functionality (auto-patch, thumbnails):

personality and CitpFixtureMapping.xml must reside in the real personality library
(usually this folder hidden/system, at D:\TitanData\Personalities).
Both files should be included there with a recent library update.
However, when copied there manually, a console software restart is required.


In both cases, MXWendler requires the CITP section activated and set correctly.


{{#mpdftags: pagebreak}}

Setup MXWendler

Switch on your MXWendler computer, set it to a suitable IP address

(usually Art-Net works well with an address like 2.x.x.x or 10.x.x.x)

Start MXWendler.

1. DMX mapping

Open the Settings menu and select the first item:

Menu → Settings → Input/Output → DMX/MIDI/Keyboard events
(Or simply press Ctrl-1.)

On this tab you can map the required actions to Art-Net channels.

Instead of mapping all channels manually, just load the prepared DMX mapping:
bottom-left click on Load and navigate to
C:\Program Files\MXWendlerStageDESIGNER50\DMX\Personalities\grandMA\FixtureLayerWith31Channels\MXWendlerDMXMappings.
Load the file MXW_08_Layers.dmxmappings.



{{#mpdftags: pagebreak}} 2. Art-Net settings


In the same settings menu toggle to the next tab:

Menu → Settings → Input/Output → DMX/Art-Net.


In the Section Art-Net:

Check the box open Art-Net
Select the correct network interface
Uncheck the box Local.
Set subnet to 0
Set DMX start channel to 1
Set Number of Universes to 1
Click on Connect and confirm the prompt.
Set Art-Net shortname to MXWendler
Set Art-Net longname to MXWendler Mediaserver.



{{#mpdftags: pagebreak}} 3. CITP settings


In the section CITP:

check activate CITP and Fixture Mode
set CITP Media Path to a suitable path with the clips you want to use
CITP Name must be MXWendler Mediaserver
Set number of layers to 8
Set DMX channels per layer to 31


The CITP settings are mandatory even if you do not want to use CITP on your lighting console.

Confirm/close the settings window with OK, and restart MXWendler to activate the settings.


{{#mpdftags: pagebreak}}

Setup your Avolites Console

1. Basic setup


Switch-on your Avolites console. Make sure it is set to a suitable IP address in the same range as the Mediaserver.

It is a good idea to check the network connection at first, i.e. by pinging both devices from each other.
If they do not ‘see’ each other then any Art-Net attempts will fail. Debugging a faulty network connection
is not covered in this document. It might however include: re-check network settings (IP address subnet mask),
check the cable, check switches/hubs if there are any, make sure firewalls are off, make sure both computers
are correctly identified…


2. Art-Net setup


From the System/Setup menu (hit <Avo> and <Disk>), select DMX Settings.

Left, in the Art-Net section, you should be able to see entries like this:
MXWendler(IP address): Universe x
Click on the entry with Universe 1, then, on the right-hand side,
click on Line 1, to route the signal from internal line 1 to Art-Net universe 1.


Next, check the Art-Net settings are correct:

left, at the Art-Net line, click on the little I
(in newer versions a symbol like this:File:Avo 04.PNG)
and make sure the settings are correct:
Enable DMX Output = Enabled
Always Broadcast ArtNet = Enabled
Network Adapter = the network adapter which you have configured

Exit the System/Settings menu.

You are now ready to patch and control MXWendler manually: <Patch>, <Fixtures>,

select manufacturer MXWendler,
select fixture MXWendler v5,
select mode Standard…
(if you want to use thumbnails then do not patch manually, but proceed straight to the next section.)


File:Avo 05.png

{{#mpdftags: pagebreak}} 3. CITP setup

Restart MXWendler again. This is required to refresh/activate the CITP data exchange.

On the Avo console, press <Patch> and select Active Fixtures.

MXWendler should be shown in the list of available active fixtures:

File:Avo 06.png

Click on this button. Usually the software sends the correct addressing automatically

(you can leave the next item on Use Fixtures Dmx Address.)
Simply click on an empty fixture button. 8 layers will automatically be patched:

File:Avo 07.png

In order to see thumbnails of your media select a mediaserver layer,

open the Attribute Editor (e.g. with <Open>-<Options>), and go to the Gobo bank: