Tutorial Eventmaster Toolset Controlling MXWendler by e.g. e2 S3 Image Processor: Difference between revisions
No edit summary |
|||
(2 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
This tutorial applies to all different OS and MXWendler versions > 6.0. | This tutorial applies to all different OS and MXWendler versions > 6.0.04 | ||
== Introduction== | == Introduction== | ||
This tutorial explains how to set up a Barco Eventmaster to trigger and control media playback on StageDesigner or FXServer. | This tutorial explains how to set up a Barco Eventmaster to trigger and control media playback on StageDesigner or FXServer. | ||
== | ==Control Setup== | ||
1. Open SD (StageDesigner) and load a clip into preload 1: | 1. Open SD (StageDesigner) and load a clip into preload 1: | ||
Line 10: | Line 10: | ||
[[File:e2_01.png|600px]] | [[File:e2_01.png|600px]] | ||
2. Open Settings->IO->Barco e2 and activate TCP listening. Also | 2. Open Settings->IO->Barco e2 and activate TCP listening. Also note down the port number. | ||
[[File:e2_02.png|600px]] | [[File:e2_02.png|600px]] | ||
3. In the Barco Eventmaster Toolset, create an 'External Device', name it e.g. 'StageDesigner' | 3. In the Barco Eventmaster Toolset, create an 'External Device', name it e.g. 'StageDesigner'. | ||
[[File:e2_03.png|600px]] | [[File:e2_03.png|600px]] | ||
4. In the 'Adjust: StageDesigner' tab, set IP address and port number | 4. In the 'Adjust: StageDesigner' tab, set IP address and port number. | ||
[[File:e2_04.png|600px]] | [[File:e2_04.png|600px]] | ||
Line 30: | Line 30: | ||
[[File:e2_05.png|600px]] | [[File:e2_05.png|600px]] | ||
6. In the 'Cue' section, add a cue | 6. In the 'Cue' section, add a cue. | ||
[[File:e2_06.png|600px]] | [[File:e2_06.png|600px]] | ||
7. In this 'Cue', add actions | 7. In this 'Cue', add actions. | ||
[[File:e2_07.png|600px]] | [[File:e2_07.png|600px]] | ||
8. From 'External Devices' drop an available command onto the 'Commands' field of the action | 8. From 'External Devices' drop an available command onto the 'Commands' field of the action. | ||
[[File:e2_08c.png|600px]] | [[File:e2_08c.png|600px]] | ||
9. Play this cue, a clip should be started in the StageDesigner |
Latest revision as of 11:25, 12 February 2024
This tutorial applies to all different OS and MXWendler versions > 6.0.04
Introduction
This tutorial explains how to set up a Barco Eventmaster to trigger and control media playback on StageDesigner or FXServer.
Control Setup
1. Open SD (StageDesigner) and load a clip into preload 1:
2. Open Settings->IO->Barco e2 and activate TCP listening. Also note down the port number.
3. In the Barco Eventmaster Toolset, create an 'External Device', name it e.g. 'StageDesigner'.
4. In the 'Adjust: StageDesigner' tab, set IP address and port number.
5. In the 'Adjust: StageDesigner' tab, add a new command. Store the command content, e.g.
- /mxw/preload/1 play to start a clip
- /mxw/preload/1 play to stop a clip
More possible commands are in the OSC control section: 3._MXW_OSC_command_reference
6. In the 'Cue' section, add a cue.
7. In this 'Cue', add actions.
8. From 'External Devices' drop an available command onto the 'Commands' field of the action.
9. Play this cue, a clip should be started in the StageDesigner